A practical phone photography guide

Photograph your crystals.
Keep the clues.

Make a useful record of your specimen’s colour, size and visible details. A phone, plain background, ruler and a few careful views are enough to begin.

About 6 minutes · By Rock & Crystal Secrets · Published 5 November 2026

Start with four photographs ↓

01 · Keep the setup simple

Start with a steady, uncluttered view.

Place the specimen on a stable surface with a plain, matte background. Clean the phone’s camera lens. Support the phone, tap the detail you want in focus and use its timer if touching the screen shakes the shot. Move back if the camera cannot focus, then check the saved image.

Begin with soft window light out of direct sun, or one diffused lamp. Avoid mixing daylight with differently coloured room lights. If a bright reflection hides detail, try a small change in angle. Note the light used so another session is easier to compare.

Keep fragile specimens supported. You do not need to wash, polish or alter a piece to photograph it; check its care guidance first.

Lighting and camera basics: GIA’s gem photography guide (opens in a new tab).

02 · Colour is a record, not a filter

Compare the photo with the piece in front of you.

Leave creative colour filters off. White balance is the camera’s adjustment for the colour of the light; an unsuitable setting can add a tint. Compare the photograph with the specimen under the same light, rather than trying to match a brighter picture found online.

A photographic grey card or colour reference can help if you already have one. Include it in a reference frame under the same lighting. Plain white paper is useful as a background but is not a calibrated colour target. Phones, screens and lighting still introduce differences.

Keep the untouched original. If you make a corrected copy, record what changed. Avoid boosting saturation to exaggerate a colour, removing marks on the specimen, or using tools that invent missing detail.

Further guidance on colour references: National Museums Scotland: photographing collections (opens in a new tab).

03 · Make size understandable

Put a real ruler in the photograph.

Place a millimetre ruler beside the specimen without leaning it against fragile points. Keep the markings approximately level with the feature you are documenting, and photograph them square-on together. A ruler far in front of or behind the piece can give a misleading comparison.

Keep the units and several divisions readable. Measure and write down the specimen’s dimensions separately; a photograph is not a precision measurement. Take another view without the ruler if you also want an uncluttered display image.

Do not add a guessed ruler or scale bar afterwards. Our collection examples below have no scale reference, so we do not infer their dimensions from the photographs.

Why include labels, a plain background and scale? DiSSCo’s specimen imaging guidance (opens in a new tab) explains the record-keeping purpose.

04 · A repeatable record

Four photographs. One useful set.

Use the same specimen ID for each image. These are suggested views for your next session, not photographs we claim to have already taken.

  1. Whole specimen

    Include the complete outline and a little space around it.

  2. Size reference

    Photograph a readable millimetre ruler beside the piece.

  3. Another side

    Show the back or underside if it can be turned safely.

  4. One close detail

    Focus on a band, pale patch, existing chip or other feature.

Add a short clip for a moving effect.

For a specimen labelled Labradorite or Tiger’s Eye, keep one lamp fixed and turn the supported piece slowly. Show a starting view, the changing effect and a return to the starting view. Keep a quieter angle as well as the brightest moment. Record any change of lighting separately, so viewers know what moved.

A flash may need a more directional light than the soft light used for an overall photograph. A still captures one angle; a clip adds movement, but neither alone proves mineral identity. Watch our Labradorite colour-flash guide →

05 · Original collection photographs

What would you photograph next?

Use these existing views to plan a more complete record. We have preserved their colours and details. The captions distinguish what is visible from a suggested next photograph.

Rounded specimen with blue-green areas, crossing dark lines and a bright curved highlight on the right.
Original Rock & Crystal Secrets photograph · Collection label: Labradorite · No scale reference shown.

Labradorite

Visible in this photograph
The blue-green area and narrow bright edge are separate features in this single view.
A useful next shot
Keep the lamp still and record a slow turn, including a less colourful angle. Watch which areas change and which lines remain visible.
Keep this limit in mind
This still cannot demonstrate moving labradorescence. A close crop also leaves part of the outer outline out of view.
Compare the labelled Labradorite photo →
Rounded rectangular specimen with blue-purple areas, cream patches and a bright pale strip across the right face.
Original Rock & Crystal Secrets photograph · Collection label: Rainbow Fluorite · No scale reference shown.

Rainbow Fluorite

Visible in this photograph
Blue-purple and cream areas meet below a bright strip of reflected light.
A useful next shot
Take a second view with the light or camera slightly repositioned. Look for detail hidden by the bright reflection, and keep both photographs.
Keep this limit in mind
The collection label is retained. Colour patches and glare do not confirm fluorite or establish a cleavage surface.
Compare the labelled Rainbow Fluorite photo →
Pale rounded specimen with fine green trails, a whitish lower-right patch and a darker lower-left area.
Original Rock & Crystal Secrets photograph · Collection label: Moss Agate · No scale reference shown.

Moss Agate

Visible in this photograph
Fine green trails cross the paler upper half; the lower-left area looks darker.
A useful next shot
Take a focused detail of one green trail, plus another whole-piece view. Keep the wider image so the detail still has a location.
Keep this limit in mind
A photograph cannot identify the chemistry of the green features. No ruler is present here, so the image does not establish the specimen’s size.
Compare the labelled Moss Agate photo →

06 · Keep the context

Make the photos part of the specimen record.

Choose a simple identifier and use it on the storage card, in your notes and in the filenames. For example, RCS-001-front.jpg, RCS-001-scale.jpg and RCS-001-detail.jpg are naming examples, not files to download.

Record the date, light source, supplied label and any edits beside the images. Keep the full frame as well as a cropped detail, and make a backup. If sharing pictures publicly, check the background, labels and location metadata for personal details first.

Your photographs can document appearance and help someone understand a question. They cannot settle every identification, treatment or origin claim. Keep an uncertain answer in the notes until there is better evidence.

Build your specimen record →

Sources and approach

Published and references checked 5 November 2026. The four-photo sequence and collection examples are Rock & Crystal Secrets’ practical suggestions. Lighting, colour-reference and documentation guidance draws on GIA, National Museums Scotland and DiSSCo (references open in new tabs). Their resources are background reading, not certification of our specimens.